Machinerie et terminologie

Cette page est divisée en deux sections, la première passe en revue les fabricants de machinerie utilisée dans le moulage sous pression et incluse une courte description de la machinerie de moulage sous pression produite par chaque compagnie. Veuillez cliquer Voir Machinerie pour voir l'équipement disponible présentement. La seconde partie, terminologie, est conçue pour clarifier les termes que nous utilisons pour décrire les caractéristiques d'une machine de moulage sous pression.

Cette page est en construction et sera mise à jour continuellement. Nous serons heureux de recevoir vos commentaires et suggestions au sujet des choses que vous aimeriez inclure sur cette page. Veuillez utiliser notre formulaire Contactez-nous pour nous faire part de vos idées. 

Manufacturiers de machinerie utilisée dans le moulage sous pression:

Terminologie du moulage sous pression (retour haut de page)

Accumulator: A pressure vessel in a hydraulic system in which hydraulic fluid is stored under nitrogen gas pressure, serving as a rapid source of hydraulic power when needed (fast shot, die close and core operations). Newer systems typically use piston type accumulators which separates the nitrogen gas charge from the hydraulic fluid via a metal piston with seals.

Auto Ladle:  A dedicated piece of electro-mechanical automation used to transfer metal from the machine furnace to the die cast machine, used on a cold chamber die casting machine. When a decision is made to change from manual die cast production to semi-automatic or fully automated, the ladle is usually the first piece of automation installed.

Automatic Operation:  The ability to run the die cast machine uninterrupted and without the need for a machine operator.

Automatic Tie Bar Puller:  An automatic method of unlocking the front nut on a tie bar, releasing the rear die height nut and using a hydraulic cylinder to pull the tie bar back to assist and speed the process of removing and installing dies. Some people refer to this same feature as "tie bar drawing" or "tie bar take-out".

Automation:

Biscuit:  Part of the metal poured into the shot sleeve, round in shape left in the shot sleeve, connected to the runners and next to the plunger at the end of the shot cylinder stroke on a cold chamber die cast machine.

Burnishing:

Bushings:

Captive:  Word used to describe a die casting operation in which the shop produces casting for its own use on a finished product. Some of these shops are also "Custom" die casters.

Cavities, Multiple: Any single die which has more than one cavity to produce multiple parts per machine cycle.

Cavity: The area in the die in which the casting is formed, the shape of the cavity is nearly the same as the part.

Center Gated:

Clamping Capacity:

Clamping Force:

Coined:

Condition, As-is:

Condition, New:

Condition, Remanufactured:

Condition, Un-Used:

Control Panel:

Core:

Core Circuit:

Core Pull Header:

Core, Fixed:

Core, Moving:

Cover, Cover Die:

Crosshead:

Crosshead Guide Bars:

Crucible:

Custom Die Caster:

DCM - Cold Chamber Machine:

DCM - Four Slide Machine:

DCM - Horizontal Clamp/Vertical Down Shot - Cold Chamber:

DCM - Hot Chamber Machine:

DCM - Hot Chamber Magnesium Machine:

DCM - Injected Metal Assembly:

DCM - Rotor Cast Machine:

DCM - Vertical Clamp/Vertical Up Shot, Cold Chamber:

Deburring:

Degassing:

Die:

Die Carrier:

Die Caster:

Die Casting:

Die Casting Machine:

Die Clamp:

Die Clamping, Automatic:

Die Clamps:

Die Close Cylinder:

Die Height Adjustment:

Die Height Adjustment-Motorized:

Die Locking Force:

Die Mounting Plate:

Die Opening Travel:

Die Spray, Fixed Head:

Die Spray, Reciprocator:

Die Stroke:

Die temperature Control Unit:

Die, Double Unit:

Die, Ejector:

Die, Master Die Set:

Die, Multiple-Cavity:

Die, Unit:

Docking Shot:

Draft:

Dross:

Eject:

Ejection Cylinder:

Ejection Force:

Ejection Mechanism:

Ejection Plate:

Ejection, Center Hydraulic:

Ejection, Drop Through:

Ejection, Hydraulic Bumper Plate:

Ejection, Integral Hydraulic:

Ejection, Mechanical Bumper Plate:

Extractor, Automatic:

Extractor, Manual:

Fast Shot:

Flash:

Four-Slide:

Furnace:

Furnace Capacity:

Furnace Drain:

Furnace Tap:

Furnace, Barrel:

Furnace, Breakdown:

Furnace, Channel:

Furnace, Charging:

Furnace, Coreless Induction:

Furnace, Core-Type:

Furnace, Crucible:

Furnace, Dosing:

Furnace, Electric:

Furnace, Holding:

Furnace, Immersed Crucible:

Furnace, Immersion:

Furnace, Level:

Furnace, Melting:

Furnace, Remelting:

Furnace, Reverberatory:

Furnace, Stack Type:

Gate Area:

Gate Runner:

Gooseneck:

Hearth:

Heel of Metal:

Helper Side:

Impact Pressure:

Induction Heating:

Ingot:

Ingot Preheater:

Injected Force:

Injection:

Injection Cylinder:

Injection Force:

Injection Pressure:

Injection Profile:

Injection System:

Injection Velocity:

Insert, Cast-In:

Intensification, Multiplier Cylinder:

Intensification, Multiplier Cylinder with Piston Assist:

Intensification, Piston:

Intensification, Pump:

Ladle:

Ladle Preheating:

Ladle, Bull:

Launder:

Launder Bussel:

Light Curtain:

Linkage Area:

Linkage Guards:

Locking Force:

Machine Size:

Machine Tonnage:

Machining, CNC:

Machining, Dedicated:

Magnesium:

Mechanical Bumper Plate:

Melt Loss:

Multiple-Slide:

Nozzle:

Nozzle Clamping Force:

Nozzle Clamps:

Nozzle Clamps, Hydraulic:

Operator's Side of Machine:

Pins:

Pins and Bushings:

Platen:

Platen, Moving:

Platen, Rear:

Platen, Stationary:

Platen, Surface:

Plunger:

Plunger Stroke:

Plunger Velocity:

Pour Hole:

Preventative Maintenance:

Projected Area:

Proportional Hydraulics:

Quench:

Quick-Change:

Real-time Shot Control:

Rebuilder (Remanufacturer):

Rheocasting:

Robot:

Safety Doors:

Safety Ratchet:

Semi-Solid:

Shot Blast:

Shot Peening:

Shot Position(s):

Shot Position Adjustment, Hydraulic:

Shot Position Adjustment, Manual:

Shot Position, Inserted:

Shot Position, Off-set:

Shot Sleeve:

Shot System:

Shot Velocity:

Slurry Cast:

Sprue:

Static Injection Force:

Telescoping Tubes:

Thermal Deburring:

Three Plate Die:

Tie Bar:

Tie Bar Balance:

Tie Bar Clearance:

Tie Bar Fatigue:

Tie Bar Force:

Tie Bar Nut:

Tie Bar Strain:

Tilting Shot Sleeve:

Toggle:

Tonnage:

Trim:

Trim Die:

T-Slots:

Two Platen Machine:

Unit Die:

Unit Die Holder:

Vacuum:

Vacuum Assist:

Valve:

Velocity, Fast Shot:

Vibratory Finishing:

Ways:

Ways & Skid Feet:

Zamak:

Zinc:

Cette page est en construction et sera mise à jour continuellement. Nous serons heureux de recevoir vos commentaires et suggestions au sujet des choses que vous aimeriez inclure sur cette page. Veuillez utiliser notre formulaire Contactez-nous pour nous faire part de vos idées.

haut de page